Vikakoodi mittaristossa

[Myju]

Terve, tuli hankittua 1997 Golffi 1.6 75hv koneella ja ajettu 237tkm. Moottori käy hienosti ja kyyti on mukavaa. Nyt kuitenkin huomasin, että moottorin käynnistyessä mittaritaulussa välkkyy kilometrimäärän paikalla muutaman kerran kuvanmukainen koodi. Mitäköhän mahtaa tarkoittaa?

Kylmänä käynnistettäessä ja liikkeelle lähdettäessä jos laittaa kytkimen pohjaan, niin kierrokset tipahtavat ja sammuu. Lähtee kuitenkin aina vaivatta käyntiin ja sen jälkeen ei ole ongelmia tyhjäkäynnin kanssa.

[M_M]

Lyhyesti, auto ilmoittaa huollon (Additional servicing work) olevan ajankohtainen. Alla pidempi selostus aiheesta lontoon murteella.

SERVICE REMINDER INDICATOR (SRI) DISPLAY
CABRIO, GOLF III, GTI, JETTA III (1993-95) JETTA (1996)
1) One of four service codes may be displayed on instrument
cluster according to mileage driven. Each service code displayed
determines type or level of maintenance required. Service code will
flash for approximately 3 seconds in odometer display window as
ignition is turned on. When servicing becomes due (every 7500 miles),
appropriate service code will flash for approximately 60 seconds. The
four service codes available for display are as follows:
* IN 00 (No Service Necessary)
* OEL (Oil Change Service) Every 7500 Miles
* IN 01 (Inspection Service) Every 15,000 Miles
* IN 02 (Additional Servicing Work) Every 30,000 Miles
2) After performing required maintenance, each effected
service code displayed must be reset individually. For example, at 15,
000 miles service codes OEL and IN 01 will both need to be reset.
3) To reset service codes, turn ignition on. Press and hold
odometer reset button located below speedometer. While holding button,
press clock reset button (lower button for digital clock) located to
left of fuel gauge. Release buttons. Programming mode is now
activated. Service code OEL1.S (distance counter) should be displayed.
4) Press clock reset button once more. 7500 miles should now
be indicated on display. Desired mileage for reset may be attained by
pressing clock reset button. Mileage displayed will decrease in
increments of 500 miles each time button is pressed. This feature
should only be used to calibrate mileage when instrument cluster is
replaced. When desired mileage is displayed, press odometer reset
button.
5) Service code OEL2.S (time counter) should be displayed.
Press clock reset button. 6 (months) will be indicated on display.
Time counter for next oil change may be set by pressing clock reset
button if instrument cluster was replaced. When desired time is
displayed, press odometer reset button.
6) Service code IN 01.S (time counter) should be displayed.
Press clock reset button. 12 (months) will be indicated on display.
Time counter for next maintenance interval may be set by pressing
clock reset button if instrument cluster was replaced. When desired
time is displayed, press odometer reset button.
7) Service code IN 02.S (distance counter) should be
displayed. Press clock reset button. 30,000 (miles) will be indicated
on display. Desired mileage for reset may be attained by pressing
clock reset button. Mileage displayed will decrease in increments of
500 miles each time button is pressed. This feature should only be
used to calibrate mileage when instrument cluster is replaced. When
desired mileage is displayed, turn ignition off. Programming is now
stored in memory.

[Myju]

Selvä homma, kiitos avusta! olisikohan tuolle kylmänä sammumiselle, mitään vihjeitä?

[zak69]

Selvä homma, kiitos avusta! olisikohan tuolle kylmänä sammumiselle, mitään vihjeitä?

Kannattais varmaan lukea vikakoodit ensiksi jos mahdollista.